Bevel Back Weatherboard B.C.11 PROFILE PRINT DATE: 1:2 @ A4 01 1. Weatherboards must be coated with at least one coat all sides prior to fixing. Fixing points must be pre-drilled minimum 1mm smaller than the fastener. SCALE: SHEET NUMBER REVISION. Under E2/AS1, a drainage cavity is required where the risk score exceeds 12 for bevel-back and six for rusticated. Set out the window head heights to suit the weatherboard dimensions. A 175mm minimum clearance to finished ground or 100mm to permanent paving. Specifying narrower rather than wider boards. Specifying single nailing to each board. Metalcraft Bevel Back Weatherboard is a traditional cladding system blending in with modern and traditional design surroundings. Metalcraft Bevel Back Weatherboard is a low cost cladding for out buildings, garages and sheds and is available in Zincalume®, Galvsteel®, Colorsteel® Endura® and Colorsteel® Maxx®.
- Bevel Back Weatherboard Installation
- Bevel Back Weatherboard Installation Nz
- Bevel Back Weatherboard Installation Tool
- Bevel Back Weatherboard Installation Panels
- Bevel Back Weatherboard Installation Kit
3MasterSpec - Horizontal
4Installation Specification - Bevel Back Cavity Fixed
5HC-BEVELBACK-201
Window Sill Detail,
Aluminium Joinery Deutsch patch crysis: software, free download pc.
6HC-BEVELBACK-202
Window Jamb Detail,
Aluminium Joinery
7HC-BEVELBACK-210
Door Head Detail,
Aluminium Joinery
8HC-BEVELBACK-211
Door Sill Detail,
Aluminium Joinery
9HC-BEVELBACK-212
Door Jamb Detail,
Bevel Back Weatherboard Installation
Aluminium Joinery
13HC-BEVELBACK-303
Enclosed Deck Balustrade to Wall Junction
16HC-BEVELBACK-410
General Detail Cavity Fix,
Stain Finish
17HC-BEVELBACK-411
Bevel Back Weatherboard Installation Nz
General Detail Cavity Fix,
Paint Finish
Bevel Back Weatherboard Installation Tool
Aluminium Joinery
9HC-BEVELBACK-212
Door Jamb Detail,
Bevel Back Weatherboard Installation
Aluminium Joinery
13HC-BEVELBACK-303
Enclosed Deck Balustrade to Wall Junction
16HC-BEVELBACK-410
General Detail Cavity Fix,
Stain Finish
17HC-BEVELBACK-411
Bevel Back Weatherboard Installation Nz
General Detail Cavity Fix,
Paint Finish
Bevel Back Weatherboard Installation Tool
Bevel Back Weatherboard Installation Panels
Bevel Back Weatherboard Installation Kit
The Hermpac Bevelback and Rebated Bevelback Weatherboard Cavity System incorporating oil or stain-finished cedar and DuraLarch weatherboards and paint finished DuraLarch and AshinDura weatherboards has been appraised as an external wall cladding system for buildings within the following scope:
- The scope limitations of NZBC Acceptable System E2/AS1 paragraph 1.1.
- Constructed with timber framing complying with the NZBC.
- With a risk score of 0-20 calculated in accordance with NZBC Acceptable Solution E2/AS1 Table 2.
- Situated in NZS 3604 wind zones up to and including extra high.
The Hermpac Bevelback and Rebated Bevelback Weatherboard Cavity System incorporating oil or stain-finished weatherboards has also been appraised for weathertightness and structural wind loading when used as an external wall cladding system for buildings within the following scope:
- The scope limitations of NZBC Acceptable Solution E2/AS1 paragraph 1.1 with regards to building height and floor plan area.
- Constructed with timber framing subject to specific engineering design.
- Situated in specific design wind pressures up to a maximum design differential ultimate limit state (ULS) of 2.5 kPa.
The Hermpac Bevelback and Rebated Bevelback Weatherboard Cavity System incorporating paint-finished cedar weatherboards has been appraised as an external wall cladding system for buildings within the following scope:
- The scope limitations of NZBC Acceptable System E2/AS1 paragraph 1.1.
- Constructed with timber framing complying with the NZBC.
- With a risk score of 0-20 calculated in accordance with NZBC Acceptable Solution E2/AS1 Table 2.
- Situated in NZS 3604 wind zones up to and including medium when studs are at maximum 600 mm centres and NZS 3604 wind zones up to and including very high when studs are at maximum 400 mm centres.
The Hermpac Bevelback and Rebated Bevelback Weatherboard Cavity System must only be installed horizontally on vertical, flat surfaces.
The Hermpac Bevelback and Rebated Bevelback Weatherboard Cavity System is appraised for use with aluminium window and door joinery that is installed with vertical jambs and horizontal heads and sills. (The Appraisal of the Hermpac Bevelback and Rebated Bevelback Weatherboard Cavity System relies on the joinery meeting the requirements of NZS 4211 for the relevant wind zone or wind pressure.)
